Latest JN0-663 Juniper JNCIP-SP Practice Test – Best Online Resource For Passing Juniper JN0-663 Exam Successfully

Now, you have a chance to pass the JN0-663 exam and earn the Service Provider Routing and Switching, Professional (JNCIP-SP) certification. We give the latest JN0-663 Juniper JNCIP-SP practice test to be your best online resource for the Juniper JNCIP-SP exam. The top team of ITExamShop has designed 94 practice exam questions and answers covering all the exam objectives for your learning. With our latest JN0-663 practice test, you can read all the related questions and answers for preparation, and we ensure that you can be confident of passing the Service Provider Routing and Switching, Professional (JNCIP-SP) JN0-663 exam.

You can read the JN0-663 free demo questions below before getting the latest practice test:

Page 1 of 2

 Loading...

1. You are creating an LDP-signaled Layer 2 circuit between two sites. Site1 and Site2 use different VLAN IDs to connect to your PE devices In this scenario, which encapsulation type must be used on the logical interfaces?

vlan-bridge

vlan-ccc

vlan-tcc

vlan-vpls

Launch demo modal

 Loading...

2. Exhibit:





Referring to the exhibit, which two statements are true? (Choose two.)

This router is an ABR

This router is an ASB

There are two interfaces marked as passive.

There is one interface marked as passive.

Launch demo modal

 Loading...

3. The link between CE1 and PE1 has a history of flapping To avoid the impact that flapping causes to the network you decide to use route damping

Which statement is correct in this scenario?

Dampened routes decay at a sliding rate known as half-life

Routes become dampened when the configured max-suppress value is reached

Dampening is enabled on interfaces

Dampened routes become active when their figure of merit drops below the reuse value.

Launch demo modal

 Loading...

4. Exhibit:





Which three statements are true about the show pim join output shown in the exhibit? (Choose three.)

This is a source-specific multicast stream.

The multicast stream does not have an R

The multicast stream has been configured with a backup path to allow for fast reroute.

The shortest path to the source is through the RP E The multicast receiver is still using the RP to receive the stream.

Launch demo modal

 Loading...

5. What is the purpose of the duster-list attribute within a BGP route reflector group?

to disable internal cluster re-advertisements

to define the router that first advertised the route to the route reflector

to override the router 10 value within the cluster

to facilitate loop detection within the route reflector network

Launch demo modal

 Loading...

6. Exhibit.





You are troubleshooting a problem with a BGP peer where BGP routes are not being accepted from that peer.

Referring to the exhibit, which two statements are correct*? (Choose two)

Term 0 is missing a terminating action that allows BGP routes to be accepted

You cannot have terminating actions outside of terms.

The reject at the end of the policy is preventing the routes from being accepted.

Term 0 is missing a route-fitter that specifies the allowed routes

Launch demo modal

 Loading...

7. Exhibit:





You notice an inconsistency between the routing table and the OSPF database, as shown in the exhibit.

What are two reasons for this behavior? (Choose two.)

The LSA is a Type 4 LS

An OSPF export policy is being applied to the route.

An OSPF import policy is being applied to the route.

The LSA is a Type 5 LS

Launch demo modal

 Loading...

8. You are asked to configure a series of interface policers and firewall filters, which include policers, on the same device You must ensure that the two configuration methods do not conflict.

What are two considerations when performing this task? (Choose two.)

On inbound traffic, interface policers are applied before firewall filters.

On inbound traffic, firewall filters are applied before interface policers.

On outbound traffic, interface policers are applied before firewall filters.

On outbound traffic, firewall filters are applied before interface policers.

Launch demo modal

 Loading...

9. You are responsible for configuring CoS for your network Your network includes a video application with strict latency requirements, so that any packets delayed by more than 75 ms are effectively useless. You want to ensure that you do not waste buffer space.

When configuring the scheduler for this application, which feature would you use?

exact

remainder

rate limit

temporal

Launch demo modal

 Loading...

10. Exhibit.





You are providing camer-of-carner VPN services for AS 100 and AS 200 You want to distribute MPLS labels between your PE routers and the AS 100 and AS 200 CE routers.

What must be enabled to accomplish this task?

Use BGP with the labeled-unicast address family enabled

Use RSVP with the tunnel-services parameter enabled

Use BGP with the inet-vpn address family enabled

Use RSVP with the lsp-set parameter enabled

Launch demo modal

Page 2 of 2

 Loading...

11. Which two statements about IS-IS are correct? (Choose two.)

Level 1 intermediate systems exchange routing information with Level 1 intermediate systems in other IS-IS areas.

An IS-IS router sets the attached bit in the PDUs it sends to a Level 1 area to indicate that it is a backbone router.

A Level 1 router can only form adjacencies with other Level 1 routers.

Level 2 routers can form adjacencies with either Level 1 or Level 2 routers.

Launch demo modal

 Loading...